• 1 – 20 t/h
  • 0.7 – 2 Mpa
  • Industrial
  • In Stock
  • Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.
  • Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.

WSN series gas / oil fired industrial horizontal steam boiler is a kind of safety and high efficiency heating equipment with fully automatic intelligent control system. It’s a boiler shell type 3 passes wetback oil/gas fired boiler. Usually, the WNS series steam boilers widely used for industry production and processing, such as textile mill, medicine industry, food & beverage industry, chemical industry, garment industry, food processing industry, and wood processing industry, moreover, it could be used for central heating in enterprise, hotel, hospital, civil architecture, etc.

Gas Water Heater Igniter Not Working - Best Wate

2019-8-27 · Water Heater Pilot Light Igniter Gas HeatersGas Water Heater IgniterHow To Light A Water Heater PilotTroubleshooting Pilot Light Problems In Gas Water HeatingRheem Protech Igniter And Bracket For Gas Water HeatersHow To Light A Gas Water Heater CHow To Replace A Water Heater Thermocouple Or Flame SensorRheem Protech Hot Surface Igniter For Gas Water

Causes for Flame Failure in a Boiler and Operator Acti

Maintaining a good flame in a boiler is the key to a good boiler performance. Unstable flame is always a threat for boiler furnace explosion, which can lead to a large outage of boiler and loss. There are many causes that can contribute to boiler flame failure. Hence it has become a practice of all boiler designers to interlock purging the boiler with boiler start-up.

How to Tell if an Ignitor on a Gas Furnace Is Workin

2018-12-4 · The igniter is not working properly if the heat does not come on after resetting it. Repeat the process once to see if it will work, or simply switch the circuit breaker on and off real fast for

014 – IGNITOR TESTING & TROUBLESHOOTING

Turn on the test power cord switch to power the ignitor. Check for spark across the ignitor clip ends (see Figure 1). If spark occurs, proceed the secondary coil test below. If spark does not jump the gap, or if the spark jumps intermittently, ignitor is defective and should be replaced. Turn off power to the ignitor.

How to Repair an Electronic Ignition Gas Furnace

The hot surface ignitor (HSI) is the most commonly used electronic ignition system. It works like a light bulb filament, heating up when electricity is passed through it. Most are made from silicon nitride or silicon carbide. The igniter is located in the flow of gas entering the burners.

Boiler Ignition Problem? | DIYnot Foru

2003-12-15 · Unfortunately the previous contractors are no longer answering their telephone number - not very reassuring! The boiler is now working intermittantly. It starts and will come on and off and heat the water for a period of time, but after a while it seems to fail to ignite. Can anyone advise if this problem could be dangerous?

Boiler Troubleshooting 101: A Homeowner's Gui

Some Radiators Not Heating. You may also come across one or more radiators not producing heat when the rest of the boiler system is working fine. If you're sure you've adjusted the radiator valve correctly to produce heat, the problem may be with a faulty circulator or zone valve, which would cause certain zones to receive hot water and

Boiler Will Not Fire — Heating Help: The Wa

Raypak H4-0090B Boiler Still Will NOt Fire Continued from my message yesterday. I ran a new ground wire from the S8910U1000 hot surface ignitor to the burner tray. The polarity is correct on L1 and L2, but it still will not light. I would appreciate any other suggestions. Please see my message posted yesterday for the complete history.

014 – IGNITOR TESTING & TROUBLESHOOTING

Turn on the test power cord switch to power the ignitor. Check for spark across the ignitor clip ends (see Figure 1). If spark occurs, proceed the secondary coil test below. If spark does not jump the gap, or if the spark jumps intermittently, ignitor is defective and should be replaced. Turn off power to the ignitor.

How to Troubleshoot a Hot Surface Ignitor (HS

How to Troubleshoot a Hot Surface Ignitor (HSI) STEP 1. Verify that all wire connections are secure from the furnace to the hot surface ignitor. STEP 2. Does the hot surface ignitor have any visible abnormal spots on it.? A burned hot surface ignitor will typically have a white or burned spot when it has failed.

Cleaver brooks boiler troubleshooting | AllBoil

Cleaver boiler troubleshooting may turn out to be easier than you expected. Just follow these simple instructions and fix your boiler on your own! Skip to content. Motor does not drive to open or close during pre-purge or close on burner shutdown. A. Motor defective. B. Loose electrical connection.

ModelRated steam capacity(t/h)Rated working pressure(Mpa)Rated steam temperature(℃)Maximum transport size(m)
(L×W×H)
WNS1-0.7-Y(Q)10.71703.3×1.8×2.1
WNS1-1.0-Y(Q)111843.3×1.8×2.1
WNS1.5-1.0-Y(Q) 1.511843.0×1.8×2.0
WNS1.5-1.25-Y(Q)1.51.251943.0×1.8×2.0
WNS2-1.0-Y(Q) 211844.4×2.1×2.5
WNS2-1.25-Y(Q)21.251944.4×2.1×2.5
WNS3-1.0-Y(Q)311844.6×2.3×2.6
WNS3-1.25-Y(Q)31.251944.6×2.3×2.6
WNS4-1.25-Y(Q)41.251944.7×2.5×2.9
WNS4-1.6-Y(Q)41.62044.7×2.5×2.9
WNS5-1.25-Y(Q)51.251945.3×2.7×3.3
WNS5-1.6-Y(Q)51.62045.3×2.7×3.3
WNS6-1.25-Y(Q)61.251945.9×2.6×3.0
WNS6-1.6-Y(Q)61.62045.9×2.6×3.0
WNS8-1.25-Y(Q)81.251945.9×2.8×3.1
WNS8-1.6-Y(Q)81.62045.9×2.8×3.1
WNS10-1.25-Y(Q)101.251947.7×2.8×3.1
WNS10-1.6-Y(Q)101.62047.7×2.8×3.1
WNS15-1.25-Y(Q)151.251947.0×3.1×3.6
WNS15-1.6-Y(Q)151.62047.0×3.1×3.6
WNS20-1.25-Y(Q)201.251948.3×3.4×4.0
WNS20-1.6-Y(Q)201.62048.3×3.4×4.0