• 1 – 20 t/h
  • 0.7 – 2 Mpa
  • Industrial
  • In Stock
  • Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.
  • Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.

WSN series gas / oil fired industrial horizontal steam boiler is a kind of safety and high efficiency heating equipment with fully automatic intelligent control system. It’s a boiler shell type 3 passes wetback oil/gas fired boiler. Usually, the WNS series steam boilers widely used for industry production and processing, such as textile mill, medicine industry, food & beverage industry, chemical industry, garment industry, food processing industry, and wood processing industry, moreover, it could be used for central heating in enterprise, hotel, hospital, civil architecture, etc.

EXCERPTS FROM: ASME BOILER AND PRESSURE VESSE

2019-9-13 · EXCERPTS FROM: ASME BOILER AND PRESSURE VESSEL CODE SECTION I − POWER BOILERS 2010 EDITION INTRODUCTION This Code covers rules for construction of power boilers1, electric boilers2, miniature boilers3, high−temperature water boilers4, heat recovery steam generators5, and certain fired pres-

Pressure Vessel Dimension Inspecti

Our nominal thickness is 20 mm, so up to 19.746 is acceptable then for the above example. The thickness dimension is also OK. So the above head dimensions are ok. Pressure Vessel Dimension Inspection - Out of Roundness of Shell: UG-80 deals with out of roundness of shell.

standard three return steam boiler oil gas boil

2012-6-28 · At full capacity a boiler of this size converts 3 000 litres of fuel oil or a corresponding amount of natural gas to thermal or process heat every The heart of an industrial boiler system is a hot water or steam boiler operated with a certain Sectional drawing of a three pass shell boiler Waste gas connection to chimney Smoke tube pass

SECTION .0500 - NON-STANDARD BOILERS AN

2018-8-14 · SECTION .0500 - NON-STANDARD BOILERS AND PRESSURE VESSELS 13 NCAC 13 .0501 GENERAL REQUIREMENTS (a) All aspects of a nonstandard boiler or pressure vessel including, but not limited to, its installation, repair, alteration, inspection, appurtenances, and operation shall conform to the ASME Code and the National Board

ENGINEERING STANDARD FOR PIPING MATERIA

2013-8-13 · ENGINEERING STANDARD . FOR . PIPING MATERIAL SELECTION (ON PLOT PIPING) PART ONE . GENERAL . FIRST EDITION . This Standard contains piping classes primarily developed for petroleum refineries, gas and IPS-D-PI-121 "Hydrostatic Test Blinds Thickness

Minimum design wall thickness of thin/thic

The formulae in ASME Section VIII, Division 1,paragraph UG-27,used for calculating the wall thickness

BS 2486-1997 Recommendations for treatment of water fo

2016-5-6 · Thus the composition of the boiler water should be maintained to the desired standard and faults diagnosed before boiler amount of solids in the steam from a shell boiler

CYLINDRICAL SHELL THICKNESS CALCULATION - Ksec

Use Cylindrical Shell thickness calculation page as part of Pressure Vessel design as per ASME Section VIII Div. 1. Calculate Cylinder shell thickness under internal Pressure & Allowable Stress of Material. Head, Cone & Nozzle thickness calculation also available

Steam Boiler Drum Thickness - thehsfoundation.o

We need know the details of steam boiler drum thickness, for example capacity, pressure, etc,please contact online service. 3.How about the quality of steam boiler drum thickness ? Our industrial steam boiler manufactured strictly according to national and international standard. our products have approved ASME, IBR, ISO9001-2008, etc. Get a quote

Standard Vessel Spec. | SA Boil

The shell thickness of our standard vessels range from 4mm to 10mm, using S355JR (300 WA) mild steel in the manufacturing process. The dish ends of our vessels range from 4mm to 10mm thickness to suit the vessel shell and consist of a 6% ellipsoidal dish manufactured from S355JR (300 WA) mild steel.

Boiler Dr

Boiler steam/water drum. Applied Area. Natural circulation boiler. Drum Shell Plate Material – Carbon Steel : Q245R, P265GH, SA516-Gr.60/65/70 – Alloy Steel : Q345R, Q375R, 15CrMoR, 12Cr1MoVR, P355GH, DIWA353 Shell Plate Thickness ≤150 mm. Drum Diameter ≤3,200 mm. Drum Length ≤17,000 mm. Welding

ModelRated steam capacity(t/h)Rated working pressure(Mpa)Rated steam temperature(℃)Maximum transport size(m)
(L×W×H)
WNS1-0.7-Y(Q)10.71703.3×1.8×2.1
WNS1-1.0-Y(Q)111843.3×1.8×2.1
WNS1.5-1.0-Y(Q) 1.511843.0×1.8×2.0
WNS1.5-1.25-Y(Q)1.51.251943.0×1.8×2.0
WNS2-1.0-Y(Q) 211844.4×2.1×2.5
WNS2-1.25-Y(Q)21.251944.4×2.1×2.5
WNS3-1.0-Y(Q)311844.6×2.3×2.6
WNS3-1.25-Y(Q)31.251944.6×2.3×2.6
WNS4-1.25-Y(Q)41.251944.7×2.5×2.9
WNS4-1.6-Y(Q)41.62044.7×2.5×2.9
WNS5-1.25-Y(Q)51.251945.3×2.7×3.3
WNS5-1.6-Y(Q)51.62045.3×2.7×3.3
WNS6-1.25-Y(Q)61.251945.9×2.6×3.0
WNS6-1.6-Y(Q)61.62045.9×2.6×3.0
WNS8-1.25-Y(Q)81.251945.9×2.8×3.1
WNS8-1.6-Y(Q)81.62045.9×2.8×3.1
WNS10-1.25-Y(Q)101.251947.7×2.8×3.1
WNS10-1.6-Y(Q)101.62047.7×2.8×3.1
WNS15-1.25-Y(Q)151.251947.0×3.1×3.6
WNS15-1.6-Y(Q)151.62047.0×3.1×3.6
WNS20-1.25-Y(Q)201.251948.3×3.4×4.0
WNS20-1.6-Y(Q)201.62048.3×3.4×4.0